Motor driver module

وحدة قيادة محركات L298N بجسر H مزدوج للتيار المستمر والمحركات الخطوية | L298N Dual H-Bridge Motor Driver Module for DC and Stepper Motors

⁨وحدة قيادة محركات L298N بجسر H مزدوج للتيار المستمر والمحركات الخطوية | L298N Dual H-Bridge Motor Driver Module for DC and Stepper Motors⁩ — ⁨4,600 IQD⁩ from ⁨Nanotik⁩ on SinaaStore. New, 1-month warranty. Delivery anywhere in Iraq for 5,000 IQD, cash on delivery.

Sold by Nanotik

Highlights

  • L298N chip with a dual H-bridge
  • Motor supply 5V to 35V DC
  • Up to 2A per channel
  • ENA and ENB inputs for PWM
  • New, with a 1-month warranty
4,600IQD5,750IQDخصم 20%In stock
1

Ask about stock or request a better price

Price

4,600IQD

Its price has held at 5,750 IQD for the last 11 days.

Cash on delivery

Pay cash when the order reaches you — nothing upfront.

Delivery across Iraq

One flat 5,000 IQD fee for the whole order.

Learn more

1-month warranty

Learn more

About this item

L298N dual H-bridge driver module for DC motors or one bipolar stepper, with 5V to 35V motor supply and up to 2A per channel.

A motor driver board built on the L298N chip with a dual H-bridge, so it controls two DC motors independently in both directions, or one bipolar stepper motor. The motor supply is 5V to 35V DC, the maximum current is 2A per channel, and it has independent channels.

Control is through the IN1-IN4 inputs plus ENA and ENB, which accept a PWM signal for speed. The board has an internal 5V regulator whose output can power a control board such as an Arduino at a suitable input voltage, a heat sink mounted on the chip, and screw terminals for motors and power with a header for control.

An important warning from the listing: remove the 5V regulator jumper if the motor voltage is above 12V, otherwise the regulator overheats and may burn out, and always join the grounds of the board and the controller or the control signals will not be read properly. It suits robot cars and line-following carts with Arduino and ESP32, speed and direction control of small DC motors, and teaching projects with bipolar steppers.

It is new with a 1 months warranty, and the box holds one L298N driver board with a mounted heat sink.

Suitable for

  • Robot cars and line-following carts
  • Controlling direction and speed of small DC motors
  • Running bipolar stepper motors in teaching projects

Seller's description

لوحة قيادة محركات مبنية على شريحة L298N تحتوي جسر H مزدوج، فتتحكم بمحركَي تيار مستمر بشكل مستقل في الاتجاهين، أو بمحرك خطوي ثنائي القطب واحد. تعمل بفولتية محرك من 5V إلى 35V بتيار يصل إلى 2A لكل قناة، وتضم منظم 5V داخلياً يمكن استخدامه لتغذية لوحة التحكم، مع مشتت حراري مثبّت فوق الشريحة.

أبرز المزايا

  • جسر H مزدوج يتحكم بمحركين DC أو محرك stepper ثنائي القطب
  • فولتية تشغيل المحرك من 5V إلى 35V وتيار حتى 2A لكل قناة
  • مداخل ENA وENB تقبل إشارة PWM للتحكم بالسرعة
  • منظم 5V داخلي يمكنه تغذية لوحة Arduino عند فولتية دخل مناسبة
  • أطراف براغي screw terminals للمحركات ومصدر القدرة
  • مشتت حراري مركّب مسبقاً فوق الشريحة

الاستخدامات الشائعة

  • السيارات الروبوتية وعربات تتبع الخط مع Arduino وESP32
  • التحكم باتجاه وسرعة محركات DC الصغيرة
  • تشغيل محركات خطوية ثنائية القطب في المشاريع التعليمية

ملاحظة: انزع جمبر منظم 5V إذا كانت فولتية المحرك أعلى من 12V وإلا سخن المنظم وقد يحترق، ووحّد الأرضي بين اللوحة والمتحكم دائماً وإلا لن تُقرأ إشارات التحكم بشكل صحيح.

What's in the box

لوحة قيادة محركات L298N واحدة مع مشتت حراري مركّب

Specifications

Driver chipL298N (جسر H مزدوج)
Motor supply voltage5V إلى 35V DC
Maximum current per channel2A
Supported motorsمحركا DC أو محرك stepper ثنائي القطب
Control inputsIN1–IN4 مع ENA وENB لإشارة PWM
عدد القنواتقناتان مستقلتان
منظم داخليمخرج 5V لتغذية لوحة التحكم
التوصيلاتأطراف براغي للمحركات والقدرة وهيدر للتحكم
التبريدمشتت حراري مثبّت فوق الشريحة
طريقة التحكم بالسرعةPWM على أطراف التمكين
CategoryRobotics, Drones & Industrial Automation
More categoriesMotion-control systems
ConditionNew
Warranty1-month warranty
SKUNTK-0360

Questions about وحدة قيادة محركات L298N بجسر H مزدوج للتيار المستمر والمحركات الخطوية | L298N Dual H-Bridge Motor Driver Module for DC and Stepper Motors

It currently costs 4,600 IQD (was 5,750 IQD) from Nanotik on SinaaStore (updated 16 November 2026).
A maximum of 2A per channel, according to the listing.
When the motor voltage is above 12V, otherwise the regulator overheats and may burn out, according to the listing.
The listing mentions use with Arduino and ESP32 in robot cars and line-following carts.
Yes, Nanotik has it in stock. After you order, the shop calls you to confirm availability and your address before shipping.
It is new, as listed by the seller.
Yes, it comes with a 1-month warranty from Nanotik. The warranty is provided by the selling shop, not by SinaaStore.
Delivery to every governorate in Iraq costs a flat 5,000 IQD for the whole order, and you pay cash on delivery after checking the order with the driver. Nothing is paid upfront.
It is sold by Nanotik on SinaaStore, the online marketplace that brings together the shops of Baghdad's al-Sinaa Street and the rest of Iraq. Order it from this page and pay cash on delivery.