RELIFEDesoldering braid

شريط سحب اللحام RELIFE RL-20A نحاسي بعرض 2mm | RELIFE RL-20A Desoldering Braid Solder Wick 2mm Copper

⁨شريط سحب اللحام RELIFE RL-20A نحاسي بعرض 2mm | RELIFE RL-20A Desoldering Braid Solder Wick 2mm Copper⁩ — ⁨4,463 IQD⁩ from ⁨Nanotik⁩ on SinaaStore. New, 1-month warranty. Delivery anywhere in Iraq for 5,000 IQD, cash on delivery.

Sold by Nanotik

Highlights

  • Copper braid 2mm wide
  • Pre-impregnated with rosin flux
  • Draws solder by capillary action
  • Recommended working temperature about 350°C
  • Spool in a protective plastic case
4,463IQD5,250IQDخصم 15%In stock
1

Ask about stock or request a better price

Price

4,463IQD

Its price has held at 5,250 IQD for the last 11 days.

Cash on delivery

Pay cash when the order reaches you — nothing upfront.

Delivery across Iraq

One flat 5,000 IQD fee for the whole order.

Learn more

1-month warranty

Learn more

About this item

RELIFE RL-20A copper desoldering braid, 2mm wide and pre-treated with flux, for cleaning solder joints, chip legs and BGA pads.

The RELIFE RL-20A desoldering braid is a fine copper braid 2mm wide, pre-impregnated with rosin flux. You lay it on the solder joint and press it with the hot iron tip, and it draws the molten solder up by capillary action, leaving the spot clean and ready for new soldering.

The 2mm width suits chip legs and small to medium solder joints, and because the braid is flux-treated you often need no extra flux. It can clean BGA pads on phone boards before refitting, fix solder bridges between pins, and remove excess solder from board holes. It is a practical alternative to a desoldering pump in tight spaces.

For a good result set the iron temperature around 350°C, cut off the solder-filled section after each use, and do not pull the braid away before the solder under it has cooled, or you may lift the copper pad off the board.

The braid comes on a spool inside a protective plastic case and should be stored in it away from moisture to prevent oxidation. The condition is new with a 1 months warranty, and the box contains one spool.

Suitable for

  • Cleaning solder joints and chip legs
  • Cleaning BGA pads on phone boards
  • Fixing solder bridges between pins

Seller's description

شريط سحب لحام من RELIFE موديل RL-20A بعرض 2mm، مصنوع من ضفيرة نحاسية ناعمة معالجة بالفلكس بتوزيع منتظم يجعل سحب القصدير سريعًا ومتكررًا على طول الشريط. يوضع الشريط فوق نقطة اللحام ويُضغط عليه بسن المكواة الساخن فيسحب القصدير المنصهر بالخاصية الشعرية ويترك النقطة نظيفة جاهزة للحام جديد.

أبرز المزايا

  • عرض 2mm مناسب لأرجل الشرائح ونقاط اللحام الصغيرة والمتوسطة
  • ضفيرة نحاسية ناعمة معالجة مسبقًا بالفلكس فلا تحتاج فلكس إضافي غالبًا
  • سحب سريع للقصدير يقلل زمن ملامسة الحرارة للوحة
  • يأتي على بكرة داخل علبة تحمي الشريط من الأتربة والأكسدة
  • لا يترك بقايا قصدير تسبب تماسًا بين الأرجل المتجاورة
  • بديل عملي عن مضخة سحب اللحام في الأماكن الضيقة

الاستخدامات الشائعة

  • تنظيف نقاط اللحام وأرجل الشرائح بعد رفع المكوّن
  • تنظيف باد الـ BGA على لوحات الهواتف قبل إعادة التركيب
  • إصلاح جسور القصدير (solder bridges) بين الأرجل
  • إزالة القصدير الزائد من فتحات اللوحة قبل تركيب مكوّن جديد

ملاحظة: اقطع الجزء المستهلك بعد كل استعمال، ولا تسحب الشريط قبل أن يبرد القصدير أسفله لئلا ترفع الباد النحاسي عن اللوحة؛ ضبط حرارة المكواة حول 350°C يعطي أفضل نتيجة.

What's in the box

بكرة واحدة من شريط RELIFE RL-20A بعرض 2mm

Specifications

BrandRELIFE
ModelRELIFE RL-20A
Width2mm
Materialضفيرة نحاسية ناعمة
Treatmentمشبّع بالفلكس (rosin flux) مسبقًا
Packagingبكرة داخل علبة بلاستيكية واقية
Recommended working temperatureحوالي 350°C على سن المكواة
مبدأ العملسحب القصدير المنصهر بالخاصية الشعرية
الاستخدامتنظيف نقاط اللحام وأرجل الشرائح ومناطق BGA
المجالصيانة الهواتف واللوحات الدقيقة
الاستهلاكيُقص الجزء المشبّع بالقصدير بعد كل استعمال
التخزينيُحفظ في العلبة بعيدًا عن الرطوبة لمنع الأكسدة
CategoryManufacturing, Maker, Lab & Test Equipment
More categoriesLab power supplies and measurement instruments
ConditionNew
Warranty1-month warranty
SKUNTK-0166

Questions about شريط سحب اللحام RELIFE RL-20A نحاسي بعرض 2mm | RELIFE RL-20A Desoldering Braid Solder Wick 2mm Copper

It currently costs 4,463 IQD (was 5,250 IQD) from Nanotik on SinaaStore (updated 16 November 2026).
The listing gives a width of 2mm.
The braid is pre-impregnated with rosin flux, so according to the listing you often need none.
The listing recommends about 350°C at the iron tip.
Yes, Nanotik has it in stock. After you order, the shop calls you to confirm availability and your address before shipping.
It is new, as listed by the seller.
Yes, it comes with a 1-month warranty from Nanotik. The warranty is provided by the selling shop, not by SinaaStore.
Delivery to every governorate in Iraq costs a flat 5,000 IQD for the whole order, and you pay cash on delivery after checking the order with the driver. Nothing is paid upfront.
It is sold by Nanotik on SinaaStore, the online marketplace that brings together the shops of Baghdad's al-Sinaa Street and the rest of Iraq. Order it from this page and pay cash on delivery.