Single-cell BMS board

لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 6A بـ3 MOSFET | 1S 6A 3.7V Li-ion 3 MOSFET BMS Protection Board for 18650

⁨لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 6A بـ3 MOSFET | 1S 6A 3.7V Li-ion 3 MOSFET BMS Protection Board for 18650⁩ — ⁨2,550 IQD⁩ from ⁨Nanotik⁩ on SinaaStore. New, 1-month warranty. Delivery anywhere in Iraq for 5,000 IQD, cash on delivery.

Sold by Nanotik

Highlights

  • For one 1S Li-ion cell at 3.7V
  • 6A continuous discharge
  • 3 MOSFET transistors
  • Automatic recovery after protection
  • New, with a 1-month warranty
2,550IQD3,000IQDخصم 15%In stock
1

Ask about stock or request a better price

Price

2,550IQD

Its price has held at 3,000 IQD for the last 11 days.

Cash on delivery

Pay cash when the order reaches you — nothing upfront.

Delivery across Iraq

One flat 5,000 IQD fee for the whole order.

Learn more

1-month warranty

Learn more

About this item

BMS protection board for one 1S Li-ion cell at 3.7V and 6A with 3 MOSFETs, for 18650 and similar cells.

A protection board for a single 3.7V lithium-ion cell designed for 6A with three MOSFET transistors, which the listing calls a middle step between small boards and high-current packs. It monitors the cell voltage constantly and disconnects the discharge path when it drops to the safe limit or when current is exceeded, and cuts charging when the cell is full. It suits single 18650 cells in devices that draw a high intermittent load.

Core values: continuous discharge current 6A, 3 MOSFET transistors, charge cut-off at about 4.25V per cell and discharge cut-off at about 2.5V per cell. The listed protection functions are overcharge, deep discharge, overcurrent and short circuit, with automatic recovery after the load is removed. The thresholds are preset, so no setup or programming is needed.

Compatible cells: 18650, 21700 and Li-po at 3.7V; it is not compatible with LiFePO4 cells at 3.2V. The terminals are B+ / B- / P- with solder pads, installation is by direct soldering inside the battery pack, and the slim board sits over the cell terminal without increasing the pack diameter.

Make sure the cell itself can handle 6A of continuous discharge, because low-current cells heat up before the protection acts and may be damaged despite the board. Suggested uses: small single-cell electric drills and screwdrivers, portable air pumps and fans, fishing lamps and head torches, and single 18650 packs in educational robot projects. In the box: one 1S, 6A BMS protection board. It is new, with a 1-month warranty.

Suitable for

  • Small single-cell electric drills and screwdrivers
  • Portable air pumps and fans
  • Fishing lamps and bright head torches

Seller's description

لوحة حماية لخلية ليثيوم أيون واحدة 3.7V مصمَّمة لتيار 6A بثلاثة ترانزستورات MOSFET، وهي درجة وسطى بين اللوحات الصغيرة والحزم عالية التيار. تراقب فولتية الخلية باستمرار وتفصل مسار التفريغ عند هبوطها إلى حد الأمان أو عند تجاوز التيار، كما تقطع الشحن عند اكتمال الخلية. مناسبة لخلايا 18650 المفردة في الأجهزة التي تسحب حملاً متقطعاً مرتفعاً.

أبرز المزايا

  • تيار تفريغ مستمر 6A بثلاثة MOSFET متوازية
  • تحمّل ذُرى تيار أعلى للأحمال المحرّكية القصيرة
  • فصل الشحن عند نحو 4.25V وفصل التفريغ عند نحو 2.5V
  • حماية قِصَر سريعة مع استرجاع تلقائي
  • لوحة نحيفة تُركَّب فوق قطب الخلية دون زيادة قطر الحزمة
  • لا تحتاج ضبطاً أو برمجة، تعمل مباشرة بعد اللحام

الاستخدامات الشائعة

  • مثاقب ومفكات كهربائية صغيرة بخلية واحدة
  • مضخات هواء ومراوح محمولة
  • كشافات صيد ومصابيح رأس عالية الإضاءة
  • حزم 18650 مفردة في مشاريع الروبوت التعليمي

ملاحظة: تأكد أن الخلية نفسها تتحمّل 6A تفريغاً مستمراً، فالخلايا منخفضة التيار تسخن قبل أن تعمل الحماية وقد تتلف رغم وجود اللوحة.

What's in the box

لوحة حماية BMS بترتيب 1S وتيار 6A واحدة

Specifications

Cell count1S خلية واحدة بجهد 3.7V
Continuous discharge6A
MOSFET count3
Charge cut-offنحو 4.25V لكل خلية
Discharge cut-offنحو 2.5V لكل خلية
Compatible cells18650 و 21700 و Li-po بجهد 3.7V
TerminalsB+ / B- / P- بمساحات لحام
عدد ترانزستورات MOSFET3
وظائف الحمايةشحن زائد، تفريغ عميق، تيار زائد، قِصَر
الاسترجاع بعد الحمايةتلقائي عند إزالة الحمل
طريقة التركيبلحام مباشر داخل حزمة البطارية
الضبط أو البرمجةغير مطلوبة، عتبات مضبوطة مسبقاً
غير متوافقة معخلايا LiFePO4 بجهد 3.2V
CategoryAutomotive, Mobility & Transport Electronics
More categoriesBattery-management systems
ConditionNew
Warranty1-month warranty
SKUNTK-0251

Questions about لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 6A بـ3 MOSFET | 1S 6A 3.7V Li-ion 3 MOSFET BMS Protection Board for 18650

It currently costs 2,550 IQD (was 3,000 IQD) from Nanotik on SinaaStore (updated 16 November 2026).
6A continuous discharge, according to the listing.
3 MOSFET transistors, according to the listing.
No, the listing says it is not compatible with LiFePO4 cells at 3.2V.
No, the thresholds are preset and no setup or programming is needed, according to the listing.
Yes, Nanotik has it in stock. After you order, the shop calls you to confirm availability and your address before shipping.
It is new, as listed by the seller.
Yes, it comes with a 1-month warranty from Nanotik. The warranty is provided by the selling shop, not by SinaaStore.
Delivery to every governorate in Iraq costs a flat 5,000 IQD for the whole order, and you pay cash on delivery after checking the order with the driver. Nothing is paid upfront.
It is sold by Nanotik on SinaaStore, the online marketplace that brings together the shops of Baghdad's al-Sinaa Street and the rest of Iraq. Order it from this page and pay cash on delivery.