Single-cell BMS board

لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 15A بـ6 MOSFET | 1S 15A 3.7V Li-ion BMS Protection Board with 6 MOSFET for 18650

⁨لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 15A بـ6 MOSFET | 1S 15A 3.7V Li-ion BMS Protection Board with 6 MOSFET for 18650⁩ — ⁨3,188 IQD⁩ from ⁨Nanotik⁩ on SinaaStore. New, 1-month warranty. Delivery anywhere in Iraq for 5,000 IQD, cash on delivery.

Sold by Nanotik

Highlights

  • 6 MOSFET transistors
  • 15A maximum, 13A continuous
  • Charge cut-off at 4.25±0.05V
  • Measures 35 × 7 × 2mm
  • New, with a 1-month warranty
3,188IQD3,750IQDخصم 15%In stock
1

Ask about stock or request a better price

Price

3,188IQD

Its price has held at 3,750 IQD for the last 11 days.

Cash on delivery

Pay cash when the order reaches you — nothing upfront.

Delivery across Iraq

One flat 5,000 IQD fee for the whole order.

Learn more

1-month warranty

Learn more

About this item

BMS protection board for a 1S Li-ion cell at 3.7V with 15A maximum discharge, 6 MOSFETs and a 35 × 7 × 2mm size, for 18650 cells.

A BMS protection board for a single lithium-ion cell at 3.7V, built on six MOSFET transistors to lower path resistance and reduce heat at high currents. It protects the cell from overcharge above 4.25V, deep discharge below 2.54V and short circuits, and works with B+, B-, P+ and P- terminals. Its size is only 35 × 7 × 2mm, so it is soldered directly onto an 18650 cell and stays inside the enclosure without adding bulk.

Core values according to the listing: maximum discharge current 15A, continuous current 13A for charging and discharging, charge cut-off at 4.25±0.05V, charge resume at 4.23±0.05V and discharge cut-off at 2.54±0.1V to prevent cell damage. Short-circuit protection recovers automatically after the load is removed.

Supported cells are Li-ion and Li-po at 3.7V, and installation is by direct soldering inside the pack. The protection functions are overcharge, deep discharge, overcurrent and short circuit. Do not use this board with LiFePO4 cells because their voltage thresholds differ.

When soldering, start with the B- terminal and then P-, using an iron at 350°C for short seconds so the protection circuit is not damaged. Suggested uses: refurbishing handheld tool batteries and LED torches, single-cell packs for portable speakers, DIY power bank projects with 18650 cells, and powering mobile Arduino and ESP32 projects. In the box: one 1S, 15A BMS protection board. It is new, with a 1-month warranty.

Suitable for

  • Refurbishing handheld tool and LED torch batteries
  • DIY power bank projects with 18650 cells
  • Powering mobile Arduino and ESP32 projects

Seller's description

لوحة حماية BMS لخلية ليثيوم أيون واحدة بجهد 3.7V، مبنية على ستة ترانزستورات MOSFET لخفض مقاومة المسار وتقليل الحرارة عند التيارات العالية. تحمي الخلية من الشحن الزائد فوق 4.25V ومن التفريغ العميق تحت 2.54V ومن القِصَر، وتعمل بأطراف B+ وB- وP+ وP-. أبعادها 35×7×2mm فقط، لذا تُلحم مباشرة على خلية 18650 وتبقى داخل العلبة دون زيادة في الحجم.

أبرز المزايا

  • ستة MOSFET تسمح بتيار تفريغ أقصى يصل إلى 15A
  • تيار شحن وتفريغ مستمر 13A دون ارتفاع حرارة ملحوظ
  • فصل الشحن عند 4.25±0.05V واستئنافه عند 4.23±0.05V
  • فصل التفريغ عند 2.54±0.1V لمنع تلف الخلية
  • حماية من القِصَر مع استرجاع تلقائي بعد إزالة الحمل
  • أبعاد نحيفة 35×7×2mm تناسب الحزم الضيقة

الاستخدامات الشائعة

  • ترميم بطاريات الأدوات اليدوية وكشافات LED
  • حزم خلية واحدة لمكبرات الصوت المحمولة
  • مشاريع باور بانك DIY بخلايا 18650
  • تغذية مشاريع Arduino وESP32 المتنقلة

ملاحظة: الحِم طرف B- أولاً ثم P- بمكواة على 350°C ولثوانٍ قصيرة حتى لا تتلف دائرة الحماية. لا تستعمل هذه اللوحة مع خلايا LiFePO4 لاختلاف عتبات الفولتية.

What's in the box

لوحة حماية BMS بترتيب 1S وتيار 15A واحدة

Specifications

Cell count1S خلية واحدة بجهد 3.7V
Maximum discharge15A
Continuous current13A شحناً وتفريغاً
Charge cut-off4.25±0.05V
Charge resume4.23±0.05V
Discharge cut-off2.54±0.1V
MOSFET count6
Dimensions35 × 7 × 2mm
TerminalsB+ / B- / P+ / P-
Supported cellsLi-ion و Li-po بجهد 3.7V
عدد ترانزستورات MOSFET6
وظائف الحمايةشحن زائد، تفريغ عميق، تيار زائد، قِصَر
طريقة التركيبلحام مباشر داخل الحزمة
CategoryAutomotive, Mobility & Transport Electronics
More categoriesBattery-management systems
ConditionNew
Warranty1-month warranty
SKUNTK-0371

Questions about لوحة حماية BMS لخلية ليثيوم أيون 1S بجهد 3.7V وتيار 15A بـ6 MOSFET | 1S 15A 3.7V Li-ion BMS Protection Board with 6 MOSFET for 18650

It currently costs 3,188 IQD (was 3,750 IQD) from Nanotik on SinaaStore (updated 16 November 2026).
35 × 7 × 2mm, according to the listing.
Maximum discharge 15A and continuous current 13A, according to the listing.
No, the listing says not to use this board with LiFePO4 cells because the voltage thresholds differ.
Start with B- then P- using an iron at 350°C for short seconds, according to the listing.
Yes, Nanotik has it in stock. After you order, the shop calls you to confirm availability and your address before shipping.
It is new, as listed by the seller.
Yes, it comes with a 1-month warranty from Nanotik. The warranty is provided by the selling shop, not by SinaaStore.
Delivery to every governorate in Iraq costs a flat 5,000 IQD for the whole order, and you pay cash on delivery after checking the order with the driver. Nothing is paid upfront.
It is sold by Nanotik on SinaaStore, the online marketplace that brings together the shops of Baghdad's al-Sinaa Street and the rest of Iraq. Order it from this page and pay cash on delivery.